STRUCT WIMAX_DEV(9) Linux Networking STRUCT WIMAX_DEV(9)NAMEstruct_wimax_dev - Generic WiMAX device
SYNOPSIS
struct wimax_dev {
struct net_device * net_dev;
struct list_head id_table_node;
struct mutex mutex;
struct mutex mutex_reset;
enum wimax_st state;
int (* op_msg_from_user) (struct wimax_dev *wimax_dev,const char *,const void *, size_t,const struct genl_info *info);
int (* op_rfkill_sw_toggle) (struct wimax_dev *wimax_dev,enum wimax_rf_state);
int (* op_reset) (struct wimax_dev *wimax_dev);
struct rfkill * rfkill;
unsigned rf_hw;
unsigned rf_sw;
char name[32];
struct dentry * debugfs_dentry;
};
MEMBERS
net_dev
[fill] Pointer to the struct net_device this WiMAX device
implements.
id_table_node
[private] link to the list of wimax devices kept by id-table.c.
Protected by it´s own spinlock.
mutex
[private] Serializes all concurrent access and execution of
operations.
mutex_reset
[private] Serializes reset operations. Needs to be a different
mutex because as part of the reset operation, the driver has to
call back into the stack to do things such as state change, that
require wimax_dev->mutex.
state
[private] Current state of the WiMAX device.
op_msg_from_user
[fill] Driver-specific operation to handle a raw message from user
space to the driver. The driver can send messages to user space
using with wimax_msg_to_user.
op_rfkill_sw_toggle
[fill] Driver-specific operation to act on userspace (or any other
agent) requesting the WiMAX device to change the RF Kill software
switch (WIMAX_RF_ON or WIMAX_RF_OFF). If such hardware support is
not present, it is assumed the radio cannot be switched off and it
is always on (and the stack will error out when trying to switch it
off). In such case, this function pointer can be left as NULL.
op_reset
[fill] Driver specific operation to reset the device. This
operation should always attempt first a warm reset that does not
disconnect the device from the bus and return 0. If that fails, it
should resort to some sort of cold or bus reset (even if it implies
a bus disconnection and device dissapearance). In that case,
-ENODEV should be returned to indicate the device is gone. This
operation has to be synchronous, and return only when the reset is
complete. In case of having had to resort to bus/cold reset
implying a device disconnection, the call is allowed to return
inmediately.
rfkill
[private] integration into the RF-Kill infrastructure.
rf_hw
[private] State of the hardware radio switch (OFF/ON)
rf_sw
[private] State of the software radio switch (OFF/ON)
name[32]
[fill] A way to identify this device. We need to register a name
with many subsystems (rfkill, workqueue creation, etc). We can´t
use the network device name as that might change and in some
instances we don´t know it yet (until we don´t call
register_netdev). So we generate an unique one using the driver
name and device bus id, place it here and use it across the board.
Recommended naming: DRIVERNAME-BUSNAME:BUSID (dev->bus->name,
dev->bus_id).
debugfs_dentry
[private] Used to hook up a debugfs entry. This shows up in the
debugfs root as wimax\:DEVICENAME.
NOTE
wimax_dev->mutex is NOT locked when this op is being called; however,
wimax_dev->mutex_reset IS locked to ensure serialization of calls to
wimax_reset. See wimax_reset´s documentation.
DESCRIPTION
This structure defines a common interface to access all WiMAX devices
from different vendors and provides a common API as well as a free-form
device-specific messaging channel.
USAGE
1. Embed a struct wimax_dev at *the beginning* the network device
structure so that netdev_priv points to it.
2. memset it to zero
3. Initialize with wimax_dev_init. This will leave the WiMAX device in
the __WIMAX_ST_NULL state.
4. Fill all the fields marked with [fill]; once called wimax_dev_add,
those fields CANNOT be modified.
5. Call wimax_dev_add *after* registering the network device. This will
leave the WiMAX device in the WIMAX_ST_DOWN state. Protect the driver´s
net_device->open against succeeding if the wimax device state is lower
than WIMAX_ST_DOWN.
6. Select when the device is going to be turned on/initialized; for
example, it could be initialized on ´ifconfig up´ (when the netdev op
´open´ is called on the driver).
When the device is initialized (at `ifconfig up` time, or right after
calling wimax_dev_add from _probe, make sure the following steps are
taken
a. Move the device to WIMAX_ST_UNINITIALIZED. This is needed so some
API calls that shouldn´t work until the device is ready can be blocked.
b. Initialize the device. Make sure to turn the SW radio switch off and
move the device to state WIMAX_ST_RADIO_OFF when done. When just
initialized, a device should be left in RADIO OFF state until user
space devices to turn it on.
c. Query the device for the state of the hardware rfkill switch and
call wimax_rfkill_report_hw and wimax_rfkill_report_sw as needed. See
below.
wimax_dev_rm undoes before unregistering the network device. Once
wimax_dev_add is called, the driver can get called on the
wimax_dev->op_* function pointers
CONCURRENCY
The stack provides a mutex for each device that will disallow API calls
happening concurrently; thus, op calls into the driver through the
wimax_dev->op*() function pointers will always be serialized and
*never* concurrent.
For locking, take wimax_dev->mutex is taken; (most) operations in the
API have to check for wimax_dev_is_ready to return 0 before continuing
(this is done internally).
REFERENCE COUNTING
The WiMAX device is reference counted by the associated network device.
The only operation that can be used to reference the device is
wimax_dev_get_by_genl_info, and the reference it acquires has to be
released with dev_put(wimax_dev->net_dev).
RFKILL
At startup, both HW and SW radio switchess are assumed to be off.
At initialization time [after calling wimax_dev_add], have the driver
query the device for the status of the software and hardware RF kill
switches and call wimax_report_rfkill_hw and wimax_rfkill_report_sw to
indicate their state. If any is missing, just call it to indicate it is
ON (radio always on).
Whenever the driver detects a change in the state of the RF kill
switches, it should call wimax_report_rfkill_hw or
wimax_report_rfkill_sw to report it to the stack.
COPYRIGHTKernel Hackers Manual 2.6. November 2013 STRUCT WIMAX_DEV(9)