MAUSEZAHN(8) netsniff-ng toolkit MAUSEZAHN(8)NAMEmausezahn - a fast versatile packet generator with Cisco-cli
SYNOPSISmausezahn { [options] "<arg-string> | <hex-string>" }
DESCRIPTIONmausezahn is a fast traffic generator which allows you to send nearly
every possible and impossible packet. In contrast to trafgen(8),
mausezahn's packet configuration is on a protocol-level instead of
byte-level and mausezahn also comes with a built-in Cisco-like command-
line interface, making it suitable as a network traffic generator box
in your network lab.
Next to network labs, it can also be used as a didactical tool and for
security audits including penetration and DoS testing. As a traffic
generator, mausezahn is also able to test IP multicast or VoIP net‐
works. Packet rates close to the physical limit are reachable, depend‐
ing on the hardware platform.
mausezahn supports two modes, ''direct mode'' and a multi-threaded
''interactive mode''.
The ''direct mode'' allows you to create a packet directly on the com‐
mand line and every packet parameter is specified in the argument list
when calling mausezahn.
The ''interactive mode'' is an advanced multi-threaded configuration
mode with its own command line interface (CLI). This mode allows you to
create an arbitrary number of packet types and streams in parallel,
each with different parameters.
The interactive mode utilizes a completely redesigned and more flexible
protocol framework called ''mops'' (mausezahn's own packet system). The
look and feel of the CLI is very close to the Cisco IOS^tm command line
interface.
You can start the interactive mode by executing mausezahn with the
''-x'' argument (an optional port number may follow, otherwise it is
25542). Then use telnet(1) to connect to this mausezahn instance. If
not otherwise specified, the default login and password combination is
mz:mz and the enable password is: mops. This can be changed in
/etc/netsniff-ng/mausezahn.conf.
The direct mode supports two specification schemes: The ''raw-layer-2''
scheme, where every single byte to be sent can be specified, and
''higher-layer'' scheme, where packet builder interfaces are used
(using the ''-t'' option).
To use the ''raw-layer-2'' scheme, simply specify the desired frame as
a hexadecimal sequence (the ''hex-string''), such as:
mausezahn eth0 "00:ab:cd:ef:00 00:00:00:00:00:01 08:00 ca:fe:ba:be"
In this example, whitespaces within the byte string are optional and
separate the Ethernet fields (destination and source address, type
field, and a short payload). The only additional options supported are
''-a'', ''-b'', ''-c'', and ''-p''. The frame length must be greater
than or equal to 15 bytes.
The ''higher-layer'' scheme is enabled using the ''-t <packet-type>''
option. This option activates a packet builder, and besides the
''packet-type'', an optional ''arg-string'' can be specified. The
''arg-string'' contains packet- specific parameters, such as TCP flags,
port numbers, etc. (see example section).
OPTIONSmausezahn provides a built-in context-specific help. Append the keyword
''help'' after the configuration options. The most important options
are:
-x [<port>]
Start mausezahn in interactive mode with a Cisco-like CLI. Use telnet
to log into the local mausezahn instance. If no port has been speci‐
fied, port 25542 is used by default.
-6
Specify IPv6 mode (IPv4 is the default).
-l <IP>
Specify the IP address mausezahn should bind to when in interactive
mode, default: 0.0.0.0.
-v
Verbose mode. Capital -V is even more verbose.
-S
Simulation mode, i.e. don't put anything on the wire. This is typically
combined with the verbose mode.
-q
Quiet mode where only warnings and errors are displayed.
-c <count>
Send the packet count times (default: 1, infinite: 0).
-d <delay>
Apply delay between transmissions. The delay value can be specified in
usec (default, no additional unit needed), or in msec (e.g. 100m or
100msec), or in seconds (e.g. 100s or 100sec). Note: mops also supports
nanosecond delay resolution if you need it (see interactive mode).
-p <length>
Pad the raw frame to specified length using zero bytes. Note that for
raw layer 2 frames the specified length defines the whole frame length,
while for higher layer packets the number of additional padding bytes
are specified.
-a <src-mac|keyword>
Use specified source MAC address with hexadecimal notation such as
00:00:aa:bb:cc:dd. By default the interface MAC address will be used.
The keywords ''rand'' and
''own'' refer to a random MAC address (only unicast addresses are cre‐
ated) and the own address, respectively. You can also use the keywords
mentioned below although broadcast-type source addresses are officially
invalid.
-b <dst-mac|keyword>
Use specified destination MAC address. By default, a broadcast is sent
in raw layer 2 mode or to the destination hosts or gateway interface
MAC address in normal (IP) mode. You can use the same keywords as men‐
tioned above, as well as
''bc'' or ''bcast'', ''cisco'', and ''stp''. Please note that for the
destination MAC address the ''rand'' keyword is supported but creates a
random address only once, even when you send multiple packets.
-A <src-ip|range|rand>
Use specified source IP address, default is own interface address.
Optionally, the keyword ''rand'' can again be used for a random source
IP address or a range can be specified, such as
''192.168.1.1-192.168.1.100'' or ''10.1.0.0/16''. Also, a DNS name can
be specified for which mausezahn tries to determine the corresponding
IP address automatically.
-B <dst-ip|range>
Use specified destination IP address (default is broadcast i.e.
255.255.255.255). As with the source address (see above) you can also
specify a range or a DNS name.
-t <packet-type [help] | help>
Create the specified packet type using the built-in packet builder.
Currently, supported packet types are: ''arp'', ''bpdu'', ''ip'',
''udp'', ''tcp'', ''rtp'', and ''dns''. Currently, there is also lim‐
ited support for ''icmp''. Type
''-t help'' to verify which packet builders your actual mausezahn ver‐
sion supports. Also, for any particular packet type, for example
''tcp'' type
''mausezahn -t tcp help'' to receive a more in-depth context specific
help.
-T <packet-type>
Make this mausezahn instance the receiving station. Currently, only
''rtp'' is an option here and provides precise jitter measurements. For
this purpose, start another mausezahn instance on the sending station
and the local receiving station will output jitter statistics. See
''mausezahn -T rtp help'' for a detailed help.
-Q <[CoS:]vlan> [, <[CoS:]vlan>, ...]
Specify 802.1Q VLAN tag and optional Class of Service. An arbitrary
number of VLAN tags can be specified (that is, you can simulate QinQ or
even QinQinQinQ..). Multiple tags must be separated via a comma or a
period (e.g. "5:10,20,2:30"). VLAN tags are not supported for ARP and
BPDU packets (in which case you could specify the whole frame in hexa‐
decimal using the raw layer 2 interface of mausezahn).
-M <label[:cos[:ttl]][bos]> [, <label...>]
Specify a MPLS label or even a MPLS label stack. Optionally, for each
label the experimental bits (usually the Class of Service, CoS) and the
Time To Live (TTL) can be specified. If you are really crazy you can
set and unset the Bottom of Stack (BoS) bit for each label using the
''S'' (set) and ''s'' (unset) option. By default, the BoS is set auto‐
matically and correctly. Any other setting will lead to invalid frames.
Enter ''-M help'' for detailed instructions and examples.
-P <ascii-payload>
Specify a cleartext payload. Alternatively, each packet type supports a
hexadecimal specification of the payload (see for example ''-t udp
help'').
-f <filename>
Read the ASCII payload from the specified file.
-F <filename>
Read the hexadecimal payload from the specified file. Actually, this
file must be also an ASCII text file, but must contain hexadecimal dig‐
its, e.g. "aa:bb:cc:0f:e6...". You can use also spaces as separation
characters.
USAGE EXAMPLE
For more comprehensive examples, have a look at the two following HOWTO
sections.
mausezahn eth0 -c 0 -d 2s -t bpdu vlan=5
Send BPDU frames for VLAN 5 as used with Cisco's PVST+ type of STP. By
default mausezahn assumes that you want to become the root bridge.
mausezahn eth0 -c 128000 -a rand -p 64
Perform a CAM table overflow attack.
mausezahn eth0 -c 0 -Q 5,100 -t tcp flags=syn,dp=1-1023 -p 20 -A rand -B
10.100.100.0/24
Perform a SYN flood attack to another VLAN using VLAN hopping. This
only works if you are connected to the same VLAN which is configured as
native VLAN on the trunk. We assume that the victim VLAN is VLAN 100
and the native VLAN is VLAN 5. Lets attack every host in VLAN 100
which use an IP prefix of 10.100.100.0/24, also try out all ports
between 1 and 1023 and use a random source IP address.
mausezahn eth0 -c 0 -d 10msec -B 230.1.1.1 -t udp dp=32000,dscp=46 -P Mul‐
ticast test packet
Send IP multicast packets to the multicast group 230.1.1.1 using a UDP
header with destination port 32000 and set the IP DSCP field to EF
(46). Send one frame every 10 msec.
mausezahn eth0 -Q 6:420 -M 100,200,300:5 -A 172.30.0.0/16 -B target.anynet‐
work.foo -t udp sp=666,dp=1-65535 -p 1000 -c 10
Send UDP packets to the destination host target.anynetwork.foo using
all possible destination ports and send every packet with all possible
source addresses of the range 172.30.0.0/16; additionally use a source
port of 666 and three MPLS labels, 100, 200, and 300, the outer (300)
with QoS field 5. Send the frame with a VLAN tag 420 and CoS 6; even‐
tually pad with 1000 bytes and repeat the whole thing 10 times.
mausezahn-t syslog sev=3 -P Main reactor reached critical temperature. -A
192.168.33.42 -B 10.1.1.9 -c 6 -d 10s
Send six forged syslog messages with severity 3 to a Syslog server
10.1.1.9; use a forged source IP address 192.168.33.42 and let
mausezahn decide which local interface to use. Use an inter-packet
delay of 10 seconds.
mausezahn-t tcp flags=syn|urg|rst, sp=145, dp=145, win=0, s=0-4294967295,
ds=1500, urg=666 -a bcast -b bcast -A bcast -B 10.1.1.6 -p 5
Send an invalid TCP packet with only a 5 byte payload as layer-2 broad‐
cast and also use the broadcast MAC address as source address. The tar‐
get should be 10.1.1.6 but use a broadcast source address. The source
and destination port shall be 145 and the window size 0. Set the TCP
flags SYN, URG, and RST simultaneously and sweep through the whole TCP
sequence number space with an increment of 1500. Finally set the urgent
pointer to 666, i.e. pointing to nowhere.
CONFIGURATION FILE
When mausezahn is run in interactive mode it automatically looks for
and reads a configuration file located at /etc/netsniff-
ng/mausezahn.conf for custom options if the file is available, other‐
wise it uses defaults set at compile time.
Config file: /etc/netsniff-ng/mausezahn.conf
The configuration file contains lines of the form:
option = value
Options supported in the configuration file are:
Option: Description:
user Username for authentication (default: mz)
password Password for authentication (default: mz)
enable Password to enter privilege mode (default: mops)
port The listening port for the CLI (default: 25542)
listen-addr IP address to bind CLI to (default: 0.0.0.0)
management-only Set management interface (no data traffic is
allowed to pass through)
cli-device Interface to bind CLI to (default: all) *not fully
implemented*
automops Path to automops file (contains XML data describing
protocols) *in development*
Example:
$ cat /etc/netsniff-ng/mausezahn.conf
user = mzadmin
password = mzpasswd
enable = privilege-mode-passwd
port = 65000
listen-addr = 127.0.0.1
INTERACTIVE MODE HOWTO
Telnet:
Using the interactive mode requires starting mausezahn as a server:
# mausezahn-x
Now you can telnet(1) to that server using the default port number
25542, but also an arbitrary port number can be specified:
# mausezahn-x 99
mausezahn accepts incoming telnet connections on port 99.
mz: Problems opening config file. Will use defaults
Either from another terminal or from another host try to telnet to the
mausezahn server:
caprica$ telnet galactica 99
Trying 192.168.0.4...
Connected to galactica.
Escape character is '^]'.
mausezahn <version>
Username: mz
Password: mz
mz> enable
Password: mops
mz#
It is recommended to configure your own login credentials in /etc/net‐
sniff-ng/mausezahn.conf, (see configuration file section)
Basics:
Since you reached the mausezahn prompt, lets try some common commands.
You can use the '?' character at any time for context-specific help.
Note that Cisco-like short form of commands are accepted in interactive
mode. For example, one can use "sh pac" instead of "show packet";
another common example is to use "config t" in place of "configure ter‐
minal". For readability, this manual will continue with the full com‐
mands.
First try out the show command:
mz# show ?
mausezahn maintains its own ARP table and observes anomalies. There is
an entry for every physical interface (however this host has only one):
mz# show arp
Intf Index IP address MAC address last Ch
UCast BCast Info
----------------------------------------------------------------------------------
eth0 [1] D 192.168.0.1 00:09:5b:9a:15:84 23:44:41 1
1 0 0000
The column Ch tells us that the announced MAC address has only changed
one time (= when it was learned). The columns Ucast and BCast tell us
how often this entry was announced via unicast or broadcast respec‐
tively.
Let's check our interfaces:
mz# show interface
Available network interfaces:
real real used (fake)
used (fake)
device IPv4 address MAC address IPv4 address
MAC address
---------------------------------------------------------------------------------------
> eth0 192.168.0.4 00:30:05:76:2e:8d 192.168.0.4
00:30:05:76:2e:8d
lo 127.0.0.1 00:00:00:00:00:00 127.0.0.1
00:00:00:00:00:00
2 interfaces found.
Default interface is eth0.
Defining packets:
Let's check the current packet list:
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
1 packets defined, 0 active.
We notice that there is already one system-defined packet process; it
has been created and used only once (during startup) by mausezahn's ARP
service. Currently, its state is config which means that the process
is sleeping.
General packet options:
Now let's create our own packet process and switch into the global con‐
figuration mode:
mz# configure terminal
mz(config)# packet
Allocated new packet PKT0002 at slot 2
mz(config-pkt-2)# ?
...
name Assign a unique name
description Assign a packet description text
bind Select the network interface
count Configure the packet count value
delay Configure the inter-packet delay
interval Configure a greater interval
type Specify packet type
mac Configure packet's MAC addresses
tag Configure tags
payload Configure a payload
port Configure packet's port numbers
end End packet configuration mode
ethernet Configure frame's Ethernet, 802.2, 802.3, or
SNAP settings
ip Configure packet's IP settings
udp Configure packet's UDP header parameters
tcp Configure packet's TCP header parameters
Here are a lot of options but normally you only need a few of them.
When you configure lots of different packets you might assign a reason‐
able name and description for them:
mz(config-pkt-2)# name Test
mz(config-pkt-2)# description This is just a test
You can, for example, change the default settings for the source and
destination MAC or IP addresses using the mac and ip commands:
mz(config-pkt-2)# ip address destination 10.1.1.0 /24
mz(config-pkt-2)# ip address source random
In the example above, we configured a range of addresses (all hosts in
the network 10.1.1.0 should be addressed). Additionally we spoof our
source IP address. Of course, we can also add one or more VLAN and, or,
MPLS tag(s):
mz(config-pkt-2)# tag ?
dot1q Configure 802.1Q (and 802.1P) parameters
mpls Configure MPLS label stack
mz(config-pkt-2)# tag dot ?
Configure 802.1Q tags:
VLAN[:CoS] [VLAN[:CoS]] ... The leftmost tag is the outer tag in
the frame
remove <tag-nr> | all Remove one or more tags (<tag-nr>
starts with 1),
by default the first (=leftmost,outer)
tag is removed,
keyword 'all' can be used instead of
tag numbers.
cfi | nocfi [<tag-nr>] Set or unset the CFI-bit in any tag (by
default
assuming the first tag).
mz(config-pkt-2)# tag dot 1:7 200:5
Configure count and delay:
mz(config-pkt-2)# count 1000
mz(config-pkt-2)# delay ?
delay <value> [hour | min | sec | msec | usec | nsec]
Specify the inter-packet delay in hours, minutes, seconds, millisec‐
onds, microseconds or nanoseconds. The default unit is milliseconds
(i.e. when no unit is given).
mz(config-pkt-2)# delay 1 msec
Inter-packet delay set to 0 sec and 1000000 nsec
mz(config-pkt-2)#
Configuring protocol types:
mausezahn's interactive mode supports a growing list of protocols and
only relies on the MOPS architecture (and not on libnet as is the case
with the legacy direct mode):
mz(config-pkt-2)# type
Specify a packet type from the following list:
arp
bpdu
igmp
ip
lldp
tcp
udp
mz(config-pkt-2)# type tcp
mz(config-pkt-2-tcp)#
....
seqnr Configure the TCP sequence number
acknr Configure the TCP acknowledgement number
hlen Configure the TCP header length
reserved Configure the TCP reserved field
flags Configure a combination of TCP flags at once
cwr Set or unset the TCP CWR flag
ece Set or unset the TCP ECE flag
urg Set or unset the TCP URG flag
ack set or unset the TCP ACK flag
psh set or unset the TCP PSH flag
rst set or unset the TCP RST flag
syn set or unset the TCP SYN flag
fin set or unset the TCP FIN flag
window Configure the TCP window size
checksum Configure the TCP checksum
urgent-pointer Configure the TCP urgent pointer
options Configure TCP options
end End TCP configuration mode
mz(config-pkt-2-tcp)# flags syn fin rst
Current setting is: --------------------RST-SYN-FIN
mz(config-pkt-2-tcp)# end
mz(config-pkt-2)# payload ascii This is a dummy payload for my first
packet
mz(config-pkt-2)# end
Now configure another packet, for example let's assume we want an LLDP
process:
mz(config)# packet
Allocated new packet PKT0003 at slot 3
mz(config-pkt-3)# type lldp
mz(config-pkt-3-lldp)# exit
mz(config)# exit
In the above example we only use the default LLDP settings and don't
configure further LLDP options or TLVs. Back in the top level of the
CLI let's verify what we had done:
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
2 Test E-Q-IT 125 config eth0
1000 usec 1000/1000 (0%)
3 PKT0003 E----- LLDP 36 config eth0
30 sec 0/0 (0%)
3 packets defined, 0 active.
The column Layers indicates which major protocols have been combined.
For example the packet with packet-id 2 ("Test") utilizes Ethernet (E),
IP (I), and TCP (T). Additionally an 802.1Q tag (Q) has been inserted.
Now start one of these packet processes:
mz# start slot 3
Activate [3]
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
2 Test E-Q-IT 125 config eth0
1000 usec 1000/1000 (0%)
3 PKT0003 E----- LLDP 36 config eth0
30 sec 0/1 (0%)
3 packets defined, 1 active.
Let's have a more detailed look at a specific packet process:
mz# show packet 2
Packet [2] Test
Description: This is just a test
State: config, Count=1000, delay=1000 usec (0 s 1000000 nsec), inter‐
val= (undefined)
Headers:
Ethernet: 00-30-05-76-2e-8d => ff-ff-ff-ff-ff-ff [0800 after 802.1Q
tag]
Auto-delivery is ON (that is, the actual MAC is adapted upon trans‐
mission)
802.1Q: 0 tag(s); (VLAN:CoS)
IP: SA=192.168.0.4 (not random) (no range)
DA=255.255.255.255 (no range)
ToS=0x00 proto=17 TTL=255 ID=0 offset=0 flags: -|-|-
len=49664(correct) checksum=0x2e8d(correct)
TCP: 83 bytes segment size (including TCP header)
SP=0 (norange) (not random), DP=0 (norange) (not random)
SQNR=3405691582 (start 0, stop 4294967295, delta 0) -- ACKNR=0
(invalid)
Flags: ------------------------SYN----, reserved field is 00,
urgent pointer= 0
Announced window size= 100
Offset= 0 (times 32 bit; value is valid), checksum= ffff
(valid)
(No TCP options attached) - 0 bytes defined
Payload size: 43 bytes
Frame size: 125 bytes
1 ff:ff:ff:ff:ff:ff:00:30 05:76:2e:8d:81:00:e0:01
81:00:a0:c8:08:00:45:00 00:67:00:00:00:00:ff:06
33 fa:e4:c0:a8:00:04:ff:ff ff:ff:00:00:00:00:ca:fe
ba:be:00:00:00:00:a0:07 00:64:f7:ab:00:00:02:04
65 05:ac:04:02:08:0a:19:35 90:c3:00:00:00:00:01:03
03:05:54:68:69:73:20:69 73:20:61:20:64:75:6d:6d
97 79:20:70:61:79:6c:6f:61 64:20:66:6f:72:20:6d:79
20:66:69:72:73:74:20:70 61:63:6b:65:74
mz#
If you want to stop one or more packet processes, use the stop command.
The "emergency stop" is when you use stop all:
mz# stop all
Stopping
[3] PKT0003
Stopped 1 transmission processe(s)
The launch command provides a shortcut for commonly used packet pro‐
cesses. For example to behave like a STP-capable bridge we want to
start an BPDU process with typical parameters:
mz# launch bpdu
Allocated new packet sysBPDU at slot 5
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
2 Test E-Q-IT 125 config eth0
1000 usec 1000/1000 (0%)
3 PKT0003 E----- LLDP 36 config eth0
30 sec 0/12 (0%)
4 PKT0004 E---I- IGMP 46 config eth0
100 msec 0/0 (0%)
5 sysBPDU ES---- BPDU 29 active eth0
2 sec 0/1 (0%)
5 packets defined, 1 active.
Now a Configuration BPDU is sent every 2 seconds, claiming to be the
root bridge (and usually confusing the LAN. Note that only packet 5
(i.e. the last row) is active and therefore sending packets while all
other packets are in state config (i.e. they have been configured but
they are not doing anything at the moment).
Configuring a greater interval:
Sometimes you may want to send a burst of packets at a greater inter‐
val:
mz(config)# packet 2
Modify packet parameters for packet Test [2]
mz(config-pkt-2)# interval
Configure a greater packet interval in days, hours, minutes, or sec‐
onds
Arguments: <value> <days | hours | minutes | seconds>
Use a zero value to disable an interval.
mz(config-pkt-2)# interval 1 hour
mz(config-pkt-2)# count 10
mz(config-pkt-2)# delay 15 usec
Inter-packet delay set to 0 sec and 15000 nsec
Now this packet is sent ten times with an inter-packet delay of 15
microseconds and this is repeated every hour. When you look at the
packet list, an interval is indicated with the additional flag 'i' when
inactive or 'I' when active:
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
2 Test E-Q-IT 125 config-i eth0
15 usec 10/10 (0%)
3 PKT0003 E----- LLDP 36 config eth0
30 sec 0/12 (0%)
4 PKT0004 E---I- IGMP 46 config eth0
100 msec 0/0 (0%)
5 sysBPDU ES---- BPDU 29 active eth0
2 sec 0/251 (0%)
5 packets defined, 1 active.
mz# start slot 2
Activate [2]
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
2 Test E-Q-IT 125 config+I eth0
15 usec 10/0 (100%)
3 PKT0003 E----- LLDP 36 config eth0
30 sec 0/12 (0%)
4 PKT0004 E---I- IGMP 46 config eth0
100 msec 0/0 (0%)
5 sysBPDU ES---- BPDU 29 active eth0
2 sec 0/256 (0%)
5 packets defined, 1 active.
Note that the flag 'I' indicates that an interval has been specified
for packet 2. The process is not active at the moment (only packet 5 is
active here) but it will become active at a regular interval. You can
verify the actual interval when viewing the packet details via the
'show packet 2' command.
Load prepared configurations:
You can prepare packet configurations using the same commands as you
would type them in on the CLI and then load them to the CLI. For exam‐
ple, assume we have prepared a file 'test.mops' containing:
configure terminal
packet
name IGMP_TEST
desc This is only a demonstration how to load a file to mops
type igmp
Then we can add this packet configuration to our packet list using the
load command:
mz# load test.mops
Read commands from test.mops...
Allocated new packet PKT0002 at slot 2
mz# show packet
Packet layer flags: E=Ethernet, S=SNAP, Q=802.1Q, M=MPLS,
I/i=IP/delivery_off, U=UDP, T=TCP
PktID PktName Layers Proto Size State Device
Delay Count/CntX
1 sysARP_servic... E----- ARP 60 config lo
100 msec 1/0 (100%)
2 IGMP_TEST E---I- IGMP 46 config eth0
100 msec 0/0 (0%)
2 packets defined, 0 active.
The file src/examples/mausezahn/example_lldp.conf contains another
example list of commands to create a bogus LLDP packet. You can load
this configuration from the mausezahn command line as follows:
mz# load /home/hh/tmp/example_lldp.conf
In case you copied the file in that path. Now when you enter 'show
packet' you will see a new packet entry in the packet list. Use the
'start slot <nr>' command to activate this packet.
You can store your own packet creations in such a file and easily load
them when you need them. Every command within such configuration files
is executed on the command line interface as if you had typed it in --
so be careful about the order and don't forget to use 'configure termi‐
nal' as first command.
You can even load other files from within a central config file.
DIRECT MODE HOWTO
How to specify hexadecimal digits:
Many arguments allow direct byte input. Bytes are represented as two
hexadecimal digits. Multiple bytes must be separated either by spaces,
colons, or dashes - whichever you prefer. The following byte strings
are equivalent:
"aa:bb cc-dd-ee ff 01 02 03-04 05"
"aa bb cc dd ee ff:01:02:03:04 05"
To begin with, you may want to send an arbitrary fancy (possibly
invalid) frame right through your network card:
mausezahn ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:08:00:ca:fe:ba:be
or equivalent but more readable:
mausezahn ff:ff:ff:ff:ff:ff-ff:ff:ff:ff:ff:ff-08:00-ca:fe:ba:be
Basic operations:
All major command line options are listed when you execute mausezahn
without arguments. For practical usage, keep the following special (not
so widely known) options in mind:
-r Multiplies the specified delay with a random
value.
-p <length> Pad the raw frame to specified length (using
random bytes).
-P <ASCII Payload> Use the specified ASCII payload.
-f <filename> Read the ASCII payload from a file.
-F <filename> Read the hexadecimal payload from a file.
-S Simulation mode: DOES NOT put anything on the
wire.
This is typically combined with one of the ver‐
bose
modes (-v or V).
Many options require a keyword or a number but the -t option is an
exception since it requires both a packet type (such as ip, udp, dns,
etc) and an argument string which is specific for that packet type.
Here are some simple examples:
mausezahn-t help
mausezahn-t tcp help
mausezahn eth3 -t udp sp=69,dp=69,p=ca:fe:ba:be
Note: Don't forget that on the CLI the Linux shell (usually the Bash)
interprets spaces as a delimiting character. That is, if you are speci‐
fying an argument that consists of multiple words with spaces in
between, you MUST group these within quotes. For example, instead of
mausezahn eth0 -t udp sp=1,dp=80,p=00:11:22:33
you could either omit the spaces
mausezahn eth0 -t udp sp=1,dp=80,p=00:11:22:33
or, for greater safety, use quotes:
mausezahn eth0 -t udp "sp=1,dp=80,p=00:11:22:33"
In order to monitor what's going on, you can enable the verbose mode
using the -v option. The opposite is the quiet mode (-q) which will
keep mausezahn absolutely quiet (except for error messages and warn‐
ings.)
Don't confuse the payload argument p=... with the padding option -p.
The latter is used outside the quotes!
The automatic packet builder:
An important argument is -t which invokes a packet builder. Currently
there are packet builders for ARP, BPDU, CDP, IP, partly ICMP, UDP,
TCP, RTP, DNS, and SYSLOG. (Additionally you can insert a VLAN tag or a
MPLS label stack but this works independently of the packet builder.)
You get context specific help for every packet builder using the help
keyword, such as:
mausezahn-t bpdu help
mausezahn-t tcp help
For every packet you may specify an optional payload. This can be done
either via hexadecimal notation using the payload (or short p) argument
or directly as ASCII text using the -P option:
mausezahn eth0 -t ip -P "Hello World" # ASCII
payload
mausezahn eth0 -t ip p=68:65:6c:6c:6f:20:77:6f:72:6c:64 # hex
payload
mausezahn eth0 -t ip "proto=89, \
p=68:65:6c:6c:6f:20:77:6f:72:6c:64, \ # same
with other
ttl=1" # IP
arguments
Note: The raw link access mode only accepts hexadecimal payloads
(because you specify everything in hexadecimal here.)
Packet count and delay:
By default only one packet is sent. If you want to send more packets
then use the count option -c <count>. When count is zero then mausezahn
will send forever. By default, mausezahn sends at maximum speed (and
this is really fast ;-)). If you don't want to overwhelm your network
devices or have other reasons to send at a slower rate then you might
want to specify a delay using the -d <delay> option.
If you only specify a numeric value it is interpreted in microsecond
units. Alternatively, for easier use, you might specify units such as
seconds, sec, milliseconds, or msec. (You can also abbreviate this with
s or m.) Note: Don't use spaces between the value and the unit! Here
are typical examples:
Send an infinite number of frames as fast as possible:
mausezahn-c 0 "aa bb cc dd ...."
Send 100,000 frames with a 50 msec interval:
mausezahn-c 100000 -d 50msec "aa bb cc dd ...."
Send an unlimited number of BPDU frames in a 2 second interval:
mausezahn-c 0 -d 2s -t bpdu conf
Note: mausezahn does not support fractional numbers. If you want to
specify for example 2.5 seconds then express this in milliseconds (2500
msec).
Source and destination addresses:
As a mnemonic trick keep in mind that all packets run from "A" to "B".
You can always specify source and destination MAC addresses using the
-a and -b options, respectively. These options also allow keywords such
as rand, own, bpdu, cisco, and others.
Similarly, you can specify source and destination IP addresses using
the -A and -B options, respectively. These options also support FQDNs
(i.e. domain names) and ranges such as 192.168.0.0/24 or
10.0.0.11-10.0.3.22. Additionally, the source address option supports
the rand keyword (ideal for "attacks").
Note: When you use the packet builder for IP-based packets (e.g. UDP or
TCP) then mausezahn automatically cares about correct MAC and IP
addresses (i.e. it performs ARP, DHCP, and DNS for you). But when you
specify at least a single link-layer address (or any other L2 option
such as a VLAN tag or MPLS header) then ARP is disabled and you must
care for the Ethernet destination address for yourself.
Layer-2:
`-- Direct link access:
mausezahn allows you to send ANY chain of bytes directly through your
Ethernet interface:
mausezahn eth0 "ff:ff:ff:ff:ff:ff ff:ff:ff:ff:ff:ff 00:00
ca:fe:ba:be"
This way you can craft every packet you want but you must do it by
hand. Note: On Wi-Fi interfaces the header is much more complicated and
automatically created by the Wi-Fi driver. As an example to introduce
some interesting options, lets continuously send frames at max speed
with random source MAC address and broadcast destination address, addi‐
tionally pad the frame to 1000 bytes:
mausezahn eth0 -c 0 -a rand -b bcast -p 1000 "08 00 aa bb cc dd"
The direct link access supports automatic padding using the -p <total
frame length> option. This allows you to pad a raw L2 frame to the
desired length. You must specify the total length, and the total frame
length must have at least 15 bytes for technical reasons. Zero bytes
are used for padding.
`-- ARP:
mausezahn provides a simple interface to the ARP packet. You can spec‐
ify the ARP method (request|reply) and up to four arguments: sendermac,
targetmac, senderip, targetip, or short smac, tmac, sip, tip. By
default, an ARP reply is sent with your own interface addresses as
source MAC and IP address, and a broadcast destination MAC and IP
address. Send a gratuitous ARP request (as used for duplicate IP
address detection):
mausezahn eth0 -t arp
ARP cache poisoning:
mausezahn eth0 -t arp "reply, senderip=192.168.0.1, target‐
mac=00:00:0c:01:02:03, \
targetip=172.16.1.50"
where by default your interface MAC address will be used as sendermac,
senderip denotes the spoofed IP address, targetmac and targetip identi‐
fies the receiver. By default, the Ethernet source address is your
interface MAC and the destination address is the broadcast address. You
can change this using the flags -a and -b.
`-- BPDU:
mausezahn provides a simple interface to the 802.1D BPDU frame format
(used to create the Spanning Tree in bridged networks). By default,
standard IEEE 802.1D BPDUs are sent and it is assumed that your com‐
puter wants to become the root bridge (rid=bid). Optionally the 802.3
destination address can be a specified MAC address, broadcast, own MAC,
or Cisco's PVST+ MAC address. The destination MAC can be specified
using the -b command which, besides MAC addresses, accepts keywords
such as bcast, own, pvst, or stp (default). PVST+ is supported as well.
Simply specify the VLAN for which you want to send a BPDU:
mausezahn eth0 -t bpdu "vlan=123, rid=2000"
See mausezahn-t bpdu help for more details.
`-- CDP:
mausezahn can send Cisco Discovery Protocol (CDP) messages since this
protocol has security relevance. Of course lots of dirty tricks are
possible; for example arbitrary TLVs can be created (using the hex-pay‐
load argument for example p=00:0e:00:07:01:01:90) and if you want to
stress the CDP database of some device, mausezahn can send each CDP
message with another system-id using the change keyword:
mausezahn-t cdp change -c 0
Some routers and switches may run into deep problems ;-) See mausezahn-t cdp help for more details.
`-- 802.1Q VLAN Tags:
mausezahn allows simple VLAN tagging for IP (and other higher layer)
packets. Simply use the option -Q <[CoS:]VLAN>, such as -Q 10 or -Q
3:921. By default CoS=0. For example send a TCP packet in VLAN 500
using CoS=7:
mausezahn eth0 -t tcp -Q 7:500 "dp=80, flags=rst, p=aa:aa:aa"
You can create as many VLAN tags as you want! This is interesting to
create QinQ encapsulations or VLAN hopping: Send a UDP packet with VLAN
tags 100 (outer) and 651 (inner):
mausezahn eth0 -t udp "dp=8888, sp=13442" -P "Mausezahn is great" -Q
100,651
Don't know if this is useful anywhere but at least it is possible:
mausezahn eth0 -t udp "dp=8888, sp=13442" -P "Mausezahn is great" \
-Q 6:5,7:732,5:331,5,6
Mix it with MPLS:
mausezahn eth0 -t udp "dp=8888, sp=13442" -P "Mausezahn is great" -Q
100,651 -M 314
When in raw Layer 2 mode you must create the VLAN tag completely by
yourself. For example if you want to send a frame in VLAN 5 using CoS
0 simply specify 81:00 as type field and for the next two bytes the CoS
(PCP), DEI (CFI), and VLAN ID values (all together known as TCI):
mausezahn eth0 -b bc -a rand "81:00 00:05 08:00 aa-aa-aa-aa-aa-aa-aa-
aa-aa"
`-- MPLS labels:
mausezahn allows you to insert one or more MPLS headers. Simply use the
option -M <label:CoS:TTL:BoS> where only the label is mandatory. If you
specify a second number it is interpreted as the experimental bits (the
CoS usually). If you specify a third number it is interpreted as TTL.
By default the TTL is set to 255. The Bottom of Stack flag is set auto‐
matically, otherwise the frame would be invalid, but if you want you
can also set or unset it using the S (set) and s (unset) argument. Note
that the BoS must be the last argument in each MPLS header definition.
Here are some examples:
Use MPLS label 214:
mausezahn eth0 -M 214 -t tcp "dp=80" -P "HTTP..." -B myhost.com
Use three labels (the 214 is now the outer):
mausezahn eth0 -M 9999,51,214 -t tcp "dp=80" -P "HTTP..." -B
myhost.com
Use two labels, one with CoS=5 and TTL=1, the other with CoS=7:
mausezahn eth0 -M 100:5:1,500:7 -t tcp "dp=80" -P "HTTP..." -B
myhost.com
Unset the BoS flag (which will result in an invalid frame):
mausezahn eth0 -M 214:s -t tcp "dp=80" -P "HTTP..." -B myhost.com
Layer 3-7:
IP, UDP, and TCP packets can be padded using the -p option. Currently
0x42 is used as padding byte ('the answer'). You cannot pad DNS packets
(would be useless anyway).
`-- IP:
mausezahn allows you to send any malformed or correct IP packet. Every
field in the IP header can be manipulated. The IP addresses can be
specified via the -A and -B options, denoting the source and destina‐
tion address, respectively. You can also specify an address range or a
host name (FQDN). Additionally, the source address can also be random.
By default the source address is your interface IP address and the des‐
tination address is a broadcast address. Here are some examples:
ASCII payload:
mausezahn eth0 -t ip -A rand -B 192.168.1.0/24 -P "hello world"
Hexadecimal payload:
mausezahn eth0 -t ip -A 10.1.0.1-10.1.255.254 -B 255.255.255.255
p=ca:fe:ba:be
Will use correct source IP address:
mausezahn eth0 -t ip -B www.xyz.com
The Type of Service (ToS) byte can either be specified directly by two
hexadecimal digits, which means you can also easily set the Explicit
Congestion Notification (ECN) bits (LSB 1 and 2), or you may only want
to specify a common DSCP value (bits 3-8) using a decimal number
(0..63):
Packet sent with DSCP = Expedited Forwarding (EF):
mausezahn eth0 -t ip dscp=46,ttl=1,proto=1,p=08:00:5a:a2:de:ad:be:af
If you leave the checksum as zero (or unspecified) the correct checksum
will be automatically computed. Note that you can only use a wrong
checksum when you also specify at least one L2 field manually.
`-- UDP:
mausezahn supports easy UDP datagram generation. Simply specify the
destination address (-B option) and optionally an arbitrary source
address (-A option) and as arguments you may specify the port numbers
using the dp (destination port) and sp (source port) arguments and a
payload. You can also easily specify a whole port range which will
result in sending multiple packets. Here are some examples:
Send test packets to the RTP port range:
mausezahn eth0 -B 192.168.1.1 -t udp "dp=16384-32767, \
p=A1:00:CC:00:00:AB:CD:EE:EE:DD:DD:00"
Send a DNS request as local broadcast (often a local router replies):
mausezahn eth0 -t udp
dp=53,p=c5-2f-01-00-00-01-00-00-00-00-00-00-03-77-77-\
77-03-78-79-7a-03-63-6f-6d-00-00-01-00-01"
Additionally you may specify the length and checksum using the len and
sum arguments (will be set correctly by default). Note: several proto‐
cols have same arguments such as len (length) and sum (checksum). If
you specified a UDP type packet (via -t udp) and want to modify the IP
length, then use the alternate keyword iplen and ipsum. Also note that
you must specify at least one L2 field which tells mausezahn to build
everything without the help of your kernel (the kernel would not allow
modifying the IP checksum and the IP length).
`-- ICMP:
mausezahn currently only supports the following ICMP methods: PING
(echo request), Redirect (various types), Unreachable (various types).
Additional ICMP types will be supported in future. Currently you would
need to tailor them by yourself, e.g. using the IP packet builder (set‐
ting proto=1). Use the mausezahn-t icmp help for help on currently
implemented options.
`-- TCP:
mausezahn allows you to easily tailor any TCP packet. Similarly as with
UDP you can specify source and destination port (ranges) using the sp
and dp arguments. Then you can directly specify the desired flags
using an "|" as delimiter if you want to specify multiple flags. For
example, a SYN-Flood attack against host 1.1.1.1 using a random source
IP address and periodically using all 1023 well-known ports could be
created via:
mausezahn eth0 -A rand -B 1.1.1.1 -c 0 -t tcp "dp=1-1023, flags=syn"
\
-P "Good morning! This is a SYN Flood Attack.
\
We apologize for any inconvenience."
Be careful with such SYN floods and only use them for firewall testing.
Check your legal position! Remember that a host with an open TCP ses‐
sion only accepts packets with correct socket information (addresses
and ports) and a valid TCP sequence number (SQNR). If you want to try a
DoS attack by sending a RST-flood and you do NOT know the target's ini‐
tial SQNR (which is normally the case) then you may want to sweep
through a range of sequence numbers:
mausezahn eth0 -A legal.host.com -B target.host.com \
-t tcp "sp=80,dp=80,s=1-4294967295"
Fortunately, the SQNR must match the target host's acknowledgement num‐
ber plus the announced window size. Since the typical window size is
something between 40000 and 65535 you are MUCH quicker when using an
increment via the ds argument:
mausezahn eth0 -A legal.host.com -B target.host.com \
-t tcp "sp=80, dp=80, s=1-4294967295, ds=40000"
In the latter case mausezahn will only send 107375 packets instead of
4294967295 (which results in a duration of approximately 1 second com‐
pared to 11 hours!). Of course you can tailor any TCP packet you like.
As with other L4 protocols mausezahn builds a correct IP header but you
can additionally access every field in the IP packet (also in the Eth‐
ernet frame).
`-- DNS:
mausezahn supports UDP-based DNS requests or responses. Typically you
may want to send a query or an answer. As usual, you can modify every
flag in the header. Here is an example of a simple query:
mausezahn eth0 -B mydns-server.com -t dns "q=www.ibm.com"
You can also create server-type messages:
mausezahn eth0 -A spoofed.dns-server.com -B target.host.com \
"q=www.topsecret.com, a=172.16.1.1"
The syntax according to the online help (-t dns help) is:
query|q = <name>[:<type>] ............. where type is per default
"A"
(and class is always "IN")
answer|a = [<type>:<ttl>:]<rdata> ...... ttl is per default 0.
= [<type>:<ttl>:]<rdata>/[<type>:<ttl>:]<rdata>/...
Note: If you only use the 'query' option then a query is sent. If you
additionally add an 'answer' then an answer is sent. Examples:
q = www.xyz.com
q = www.xyz.com, a=192.168.1.10
q = www.xyz.com, a=A:3600:192.168.1.10
q = www.xyz.com, a=CNAME:3600:abc.com/A:3600:192.168.1.10
Please try out mausezahn-t dns help to see the many other optional
command line options.
`-- RTP and VoIP path measurements:
mausezahn can send arbitrary Real Time Protocol (RTP) packets. By
default a classical G.711 codec packet of 20 ms segment size and 160
bytes is assumed. You can measure jitter, packet loss, and reordering
along a path between two hosts running mausezahn. The jitter measure‐
ment is either done following the variance low-pass filtered estimation
specified in RFC 3550 or using an alternative "real-time" method which
is even more precise (the RFC-method is used by default). For example
on Host1 you start a transmission process:
mausezahn-t rtp -B 192.168.1.19
And on Host2 (192.168.1.19) a receiving process which performs the mea‐
surement:
mausezahn-T rtp
Note that the option flag with the capital "T" means that it is a
server RTP process, waiting for incoming RTP packets from any mausezahn
source. In case you want to restrict the measurement to a specific
source or you want to perform a bidirectional measurement, you must
specify a stream identifier. Here is an example for bidirectional mea‐
surements which logs the running jitter average in a file:
Host1# mausezahn-t rtp id=11:11:11:11 -B 192.168.2.2 &
Host1# mausezahn-T rtp id=22:22:22:22 "log, path=/tmp/mz/"
Host2# mausezahn-t rtp id=22:22:22:22 -B 192.168.1.1 &
Host2# mausezahn-T rtp id=11:11:11:11 "log, path=/tmp/mz/"
In any case the measurements are printed continuously onto the screen;
by default it looks like this:
0.00 0.19 0.38
0.57
|-------------------------|-------------------------|-------------------------|
#########
0.07 msec
####################
0.14 msec
##
0.02 msec
###
0.02 msec
#########
0.07 msec
####
0.03 msec
#########
0.07 msec
#############
0.10 msec
##
0.02 msec
###########################################
0.31 msec
#########
0.07 msec
##############################################
0.33 msec
###############
0.11 msec
##########
0.07 msec
###############
0.11 msec
##########################################################
0.42 msec
#####
0.04 msec
More information is shown using the txt keyword:
mausezahn-T rtp txt
Got 100 packets from host 192.168.0.3: 0 lost (0 absolute lost), 1
out of order
Jitter_RFC (low pass filtered) = 30 usec
Samples jitter (min/avg/max) = 1/186/2527 usec
Delta-RX (min/avg/max) = 2010/20167/24805 usec
Got 100 packets from host 192.168.0.3: 0 lost (0 absolute lost), 1
out of order
Jitter_RFC (low pass filtered) = 17 usec
Samples jitter (min/avg/max) = 1/53/192 usec
Delta-RX (min/avg/max) = 20001/20376/20574 usec
Got 100 packets from host 192.168.0.3: 0 lost (0 absolute lost), 1
out of order
Jitter_RFC (low pass filtered) = 120 usec
Samples jitter (min/avg/max) = 0/91/1683 usec
Delta-RX (min/avg/max) = 18673/20378/24822 usec
See mausezahn-t rtp help and mz -T rtp help for more details.
`-- Syslog:
The traditional Syslog protocol is widely used even in professional
networks and is sometimes vulnerable. For example you might insert
forged Syslog messages by spoofing your source address (e.g. imperson‐
ate the address of a legit network device):
mausezahn-t syslog sev=3 -P "You have been mausezahned." -A
10.1.1.109 -B 192.168.7.7
See mausezahn-t syslog help for more details.
NOTE
When multiple ranges are specified, e.g. destination port ranges and
destination address ranges, then all possible combinations of ports and
addresses are used for packet generation. Furthermore, this can be
mixed with other ranges e.g. a TCP sequence number range. Note that
combining ranges can lead to a very huge number of frames to be sent.
As a rule of thumb you can assume that about 100,000 frames and more
are sent in a fraction of one second, depending on your network inter‐
face.
mausezahn has been designed as a fast traffic generator so you might
easily overwhelm a LAN segment with myriads of packets. And because
mausezahn could also support security audits it is possible to create
malicious or invalid packets, SYN floods, port and address sweeps, DNS
and ARP poisoning, etc.
Therefore, don't use this tool when you are not aware of the possible
consequences or have only a little knowledge about networks and data
communication. If you abuse mausezahn for 'unallowed' attacks and get
caught, or damage something of your own, then this is completely your
fault. So the safest solution is to try it out in a lab environment.
Also have a look at the netsniff-ng(8) note section on how you can
properly setup and tune your system.
LEGALmausezahn is licensed under the GNU GPL version 2.0.
HISTORYmausezahn was originally written by Herbert Haas. According to his web‐
site [1], he unfortunately passed away in 2011 thus leaving this tool
unmaintained. It has been adopted and integrated into the netsniff-ng
toolkit and is further being maintained and developed from there. Main‐
tainers are Tobias Klauser <tklauser@distanz.ch> and Daniel Borkmann
<dborkma@tik.ee.ethz.ch>.
[1] http://www.perihel.at/
SEE ALSOnetsniff-ng(8), trafgen(8), ifpps(8), bpfc(8), flowtop(8), astracer‐
oute(8), curvetun(8)AUTHOR
Manpage was written by Herbert Haas and modified by Daniel Borkmann.
COLOPHON
This page is part of the Linux netsniff-ng toolkit project. A descrip‐
tion of the project, and information about reporting bugs, can be found
at http://netsniff-ng.org/.
Linux 03 March 2013 MAUSEZAHN(8)