sppp man page on GhostBSD

Man page or keyword search:  
man Server   9747 pages
apropos Keyword Search (all sections)
Output format
GhostBSD logo
[printable version]

SPPP(4)			 BSD Kernel Interfaces Manual		       SPPP(4)

NAME
     sppp — point to point protocol network layer for synchronous lines

SYNOPSIS
     device sppp

DESCRIPTION
     The sppp network layer implements the state machine and the Link Control
     Protocol (LCP) of the point to point protocol (PPP) as described in RFC
     1661.  Note that this layer does not provide network interfaces of its
     own, it is rather intended to be layered on top of drivers providing a
     synchronous point-to-point connection that wish to run a PPP stack over
     it.  The corresponding network interfaces have to be provided by these
     hardware drivers.

     The sppp layer provides three basic modes of operation.  The default
     mode, with no special flags to be set, is to create the PPP connection
     (administrative Open event to the LCP layer) as soon as the interface is
     taken up with the ifconfig(8) command.  Taking the interface down again
     will terminate the LCP layer and thus all other layers on top.  The link
     will also terminate itself as soon as no Network Control Protocol (NCP)
     is open anymore, indicating that the lower layers are no longer needed.

     Setting the link-level flag link0 with ifconfig(8) will cause the respec‐
     tive network interface to go into passive mode.  This means, the adminis‐
     trative Open event to the LCP layer will be delayed until after the lower
     layers signals an Up event (rise of “carrier”).  This can be used by
     lower layers to support a dialin connection where the physical layer is
     not available immediately at startup, but only after some external event
     arrives.  Receipt of a Down event from the lower layer will not take the
     interface completely down in this case.

     Finally, setting the flag link1 will cause the interface to operate in
     dial-on-demand mode.  This is also only useful if the lower layer sup‐
     ports the notion of a carrier.  Upon configuring the respective inter‐
     face, it will delay the administrative Open event to the LCP layer until
     either an outbound network packet arrives, or until the lower layer sig‐
     nals an Up event, indicating an inbound connection.  As with passive
     mode, receipt of a Down event (loss of carrier) will not automatically
     take the interface down, thus it remains available for further connec‐
     tions.

     The sppp layer supports the debug interface flag that can be set with
     ifconfig(8).  If this flag is set, the various control protocol packets
     being exchanged as well as the option negotiation between both ends of
     the link will be logged at level LOG_DEBUG.  This can be helpful to exam‐
     ine configuration problems during the first attempts to set up a new con‐
     figuration.  Without this flag being set, only the major phase transi‐
     tions will be logged at level LOG_INFO.

     It is possible to leave the local interface IP address open for negotia‐
     tion by setting it to 0.0.0.0.  This requires that the remote peer can
     correctly supply a value for it based on the identity of the caller, or
     on the remote address supplied by this side.  Due to the way the IPCP
     option negotiation works, this address is being supplied late during the
     negotiation, which might cause the remote peer to make wrong assumptions.

     In a similar spirit the remote address can be set to the magical value
     0.0.0.* which means that we do not care what address the remote side will
     use, as long as it is not 0.0.0.0.	 This is useful if your ISP has sev‐
     eral dial-in servers.  You can of course route add something_or_other
     0.0.0.* and it will do exactly what you would want it to.

     The PAP and CHAP authentication protocols as described in RFC 1334, and
     RFC 1994 resp., are also implemented.  Their parameters are being con‐
     trolled by the spppcontrol(8) utility.

     VJ header compression is implemented, and enabled by default.  It can be
     disabled using spppcontrol(8).

DIAGNOSTICS
     <ifname><ifnum>: <proto> illegal <event> in state <statename>  An event
     happened that should not happen for the current state the respective con‐
     trol protocol is in.  See RFC 1661 for a description of the state automa‐
     ton.

     <ifname><ifnum>: loopback	The state automaton detected a line loopback
     (that is, it was talking with itself).  The interface will be temporarily
     disabled.

     <ifname><ifnum>: up  The LCP layer is running again, after a line loop‐
     back had previously been detected.

     <ifname><ifnum>: down  The keepalive facility detected the line being
     unresponsive.  Keepalive must be explicitly requested by the lower layers
     in order to take place.

SEE ALSO
     inet(4), intro(4), ppp(4), ifconfig(8), spppcontrol(8)

     W. Simpson, Editor, The Point-to-Point Protocol (PPP), RFC 1661.

     G. McGregor, The PPP Internet Protocol Control Protocol (IPCP), RFC 1332.

     B. Lloyd and W. Simpson, PPP Authentication Protocols, RFC 1334.

     W. Simpson, PPP Challenge Handshake Authentication Protocol (CHAP), RFC
     1994.

AUTHORS
     The original implementation of sppp was written in 1994 at Cronyx Ltd.,
     Moscow by Serge Vakulenko ⟨vak@cronyx.ru⟩.	 Jörg Wunsch
     ⟨joerg_wunsch@uriah.heep.sax.de⟩ rewrote a large part in 1997 in order to
     fully implement the state machine as described in RFC 1661, so it could
     also be used for dialup lines.  He also wrote this man page.  Serge later
     on wrote a basic implementation for PAP and CHAP, which served as the
     base for the current implementation, done again by Jörg Wunsch.

BUGS
     Many.

     Currently, only the IPCP control protocol and ip(4) network protocol is
     supported.	 More NCPs should be implemented, as well as other control
     protocols for authentication and link quality reporting.

     Negotiation loop avoidance is not fully implemented.  If the negotiation
     does not converge, this can cause an endless loop.

     The various parameters that should be adjustable per RFC 1661 are cur‐
     rently hard-coded into the kernel, and should be made accessible through
     spppcontrol(8).

     Passive mode has not been tested extensively.

     Link-level compression protocols should be supported.

BSD				 May 25, 2008				   BSD
[top]

List of man pages available for GhostBSD

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net