SCSITAPE(1)SCSITAPE(1)NAMEscsitape - control SCSI tape devices
SYNOPSISscsitape [-f <scsi-generic-device>] commands
DESCRIPTION
The scsitape command controls SCSI tape drives in a platform-indepen‐
dent manner. As long as 'mtx' works on the platform, so does 'scsi‐
tape'.
Note that 'scsitape' and your OS's native tape driver may stomp on each
other. In particular, if you use 'setblk' and your OS's native tape
driver has a different notion of the block size, you may get evil
results. It is recommended to use 'scsitape' only for software where
you've written your own low-level READ and WRITE routines that use the
SCSI command set to directly talk to tape drives (i.e., you do not use
the OS's native tape driver at all).
OPTIONS
The first argument, given following -f , is the SCSI generic device
corresponding to your tape drive. Consult your operating system's doc‐
umentation for more information (for example, under Linux these are
generally /dev/sg0 through /dev/sg15, under FreeBSD these are
/dev/pass0 through /dev/passX. Under Solaris this is usually the same
as your tape drive (Solaris has a SCSI passthrough ioctl). You can set
the STAPE or TAPE environment variable rather than use -f.
COMMANDS
setblk <n>
Set the tape drive's SCSI block size to <n> bytes. (NOTE: if
you are using your OS's native tape driver, THIS IS EVIL!).
fsf <n> Go forward by <n> tapemarks.
bsf <n> Go to immediately previous the <n>th previous tapemark.
(WARNING: This probably doesn't do what you expect -- e.g. if
you are immediately after a tapemark and type 'bfs 1', it
moves to immediately *before* that tape mark, for a sum total
of zero effective movement!).
eod Go to end of data.
rewind Rewind the tape drive.
eject Eject the tape currently in the drive.
erase Does a *short* erase (warning: does NOT work on all drives!).
mark <n>
write <n> filemarks ( 'mark 0' flushes the drive's buffers
).
seek <n> Seek to a logical position <n> that was reported by a previ‐
ous 'tapeinfo' command.
write <blocksize>
write blocks from stdin to the tape. Chunk the data into
<blocksize>-sized chunks. *DOES NOT WRITE OUT A TAPEMARK!*
(you will need to use a subsequent mark 1 command to write
out a tape mark).
read [<blocksize>] [ <#blocks/#bytes> ]
read blocks from the tape, write them to stdout. If we are in
variable block mode, <blocksize> should be zero (note: The
maximum block size we currently support in variable block
mode is 128K, MAX_READ_SIZE will need to be turned into a
settable variable to allow bigger reads). If <blocksize> is
ommitted, we assume that we're in variable block mode, and
that we are going to read from tape until we hit a tapemark
or end of partition or end of tape.
AUTHORS
This program was written by Eric Lee Green <eric@badtux.org>. Major
portions of the 'mtxl.c' library used herein were written by Leonard
Zubkoff.
The SCSI read and write routines are based upon those that Richard Fish
wrote for Enhanced Software Technology's BRU 16.1 product, substan‐
tially modified to work in our particular environment (in particular,
all the variable block stuff is new since BRU only does fixed block
reads and writes, and the BRU code uses bitmasks rather than bitfields
for the various flags and such in return values, as well as the BRU
code having a different SCSI API and having variable names considerably
shorter than the rather sesquipedalian 'mtx' identifiers). As required
by 'mtxl.c', these routines are licensed under the GNU General Public
License.
HINTS
Under Linux, cat /proc/scsi/scsi will tell you what SCSI devices you
have. You can then refer to them as /dev/sga, /dev/sgb, etc. by the
order they are reported.
Under FreeBSD, camcontrol devlist will tell you what SCSI devices you
have, along with which pass device controls them.
Under Solaris 7 and 8, /usr/sbin/devfsadm -C will clean up your
/devices directory. Then find /devices -name 'st@*' -print will return
a list of all tape drives. /dev on Solaris is apparently only of his‐
torical interest.
BUGS AND LIMITATIONS
for scsitape read 0 <n> where you are doing variable-block-size reads
and wish for <n> bytes, it instead reads one and exactly one block from
tape and prints that (no matter what its size). Use 'dd' on the output
of scsitape if you want finer control.
scsitape read 0 attempts reads of MAX_READ_SIZE, which is currently
128K. If blocks on tape are larger than 128K, only the first 128K will
be read -- the remainder will be silently dumped in the toilet.
This program does not interact well (or at all :-) with your OS's
native tape driver. You will likely see weird things happen if you
attempt to intermingle scsitape commands with native tape driver opera‐
tions. Note that BRU 16.1 for Solaris (and possibly others, but Solaris
I know about) will have a 'scsi' keyword to bypass the native tape
driver and write via direct uscsi commands, so if you use ´scsitape´ to
bypass the flaws of the native Solaris driver, you can use BRU 16.1 to
write your actual tape archives. (Assuming that BRU 16.1 has been
released at the time that you read this).
AVAILABILITY
This version of scsitape is currently being maintained by Robert Nelson
<robertnelson@users.sourceforge.net> as part of the 'mtx' suite of pro‐
grams. The 'mtx' home page is http://mtx.sourceforge.net and the actual
code is currently available there and via SVN from http://source‐
forge.net/projects/mtx.
SEE ALSOloaderinfo(1),tapeinfo(1),mtx(1)
SCSITAPE1.0 SCSITAPE(1)
