sac(1M) System Administration Commands sac(1M)NAMEsac - service access controller
SYNOPSISsac-t sanity_interval
/usr/lib/saf/sac
DESCRIPTION
The Service Access Controller (SAC) is the overseer of the server
machine. It is started when the server machine enters multiuser mode.
The SAC performs several important functions as explained below.
Customizing the SAC Environment
When sac is invoked, it first looks for the per-system configuration
script /etc/saf/_sysconfig. sac interprets _sysconfig to customize its
own environment. The modifications made to the SAC environment by
_sysconfig are inherited by all the children of the SAC. This inherited
environment may be modified by the children.
Starting Port Monitors
After it has interpreted the _sysconfig file, the sac reads its admin‐
istrative file /etc/saf/_sactab. _sactab specifies which port monitors
are to be started. For each port monitor to be started, sac forks a
child (see fork(2)) and creates a utmpx entry with the type field set
to LOGIN_PROCESS. Each child then interprets its per-port monitor con‐
figuration script /etc/saf/pmtag/_config , if the file exists. These
modifications to the environment affect the port monitor and will be
inherited by all its children. Finally, the child process execs the
port monitor, using the command found in the _sactab entry. (See
sacadm; this is the command given with the -c option when the port mon‐
itor is added to the system.)
Polling Port Monitors to Detect Failure
The -t option sets the frequency with which sac polls the port monitors
on the system. This time may also be thought of as half of the maximum
latency required to detect that a port monitor has failed and that
recovery action is necessary.
Administrative functions
The Service Access Controller represents the administrative point of
control for port monitors. Its administrative tasks are explained
below.
When queried (sacadm with either -l or -L), the Service Access Con‐
troller returns the status of the port monitors specified, which
sacadm prints on the standard output. A port monitor may be in one of
six states:
ENABLED The port monitor is currently running and is accepting
connections. See sacadm(1M) with the -e option.
DISABLED The port monitor is currently running and is not accept‐
ing connections. See sacadm with the -d option, and see
NOTRUNNING, below.
STARTING The port monitor is in the process of starting up. START‐
ING is an intermediate state on the way to ENABLED or
DISABLED.
FAILED The port monitor was unable to start and remain running.
STOPPING The port monitor has been manually terminated but has not
completed its shutdown procedure. STOPPING is an interme‐
diate state on the way to NOTRUNNING.
NOTRUNNING The port monitor is not currently running. (See sacadm
with -k.) This is the normal "not running" state. When a
port monitor is killed, all ports it was monitoring are
inaccessible. It is not possible for an external user to
tell whether a port is not being monitored or the system
is down. If the port monitor is not killed but is in the
DISABLED state, it may be possible (depending on the port
monitor being used) to write a message on the inaccessi‐
ble port telling the user who is trying to access the
port that it is disabled. This is the advantage of having
a DISABLED state as well as the NOTRUNNING state.
When a port monitor terminates, the SAC removes the utmpx entry for
that port monitor.
The SAC receives all requests to enable, disable, start, or stop port
monitors and takes the appropriate action.
The SAC is responsible for restarting port monitors that terminate.
Whether or not the SAC will restart a given port monitor depends on two
things:
o The restart count specified for the port monitor when the
port monitor was added by sacadm; this information is
included in /etc/saf/pmtag/_sactab.
o The number of times the port monitor has already been
restarted.
SECURITYsac uses pam(3PAM) for session management. The PAM configuration pol‐
icy, listed through /etc/pam.conf, specifies the session management
module to be used for sac. Here is a partial pam.conf file with entries
for sac using the UNIX session management module.
sac session required pam_unix_session.so.1
If there are no entries for the sac service, then the entries for the
"other" service will be used.
OPTIONS-t sanity_interval Sets the frequency (sanity_interval) with which
sac polls the port monitors on the system.
FILES
o /etc/saf/_sactab
o /etc/saf/_sysconfig
o /var/adm/utmpx
o /var/saf/_log
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬─────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼─────────────────────────────┤
│Availability │SUNWcs │
└─────────────────────────────┴─────────────────────────────┘
SEE ALSOpmadm(1M), sacadm(1M), fork(2)pam(3PAM), pam.conf(4), attributes(5),
pam_authtok_check(5), pam_authtok_get(5), pam_authtok_store(5),
pam_dhkeys(5), pam_passwd_auth(5), pam_unix_account(5),
pam_unix_auth(5), pam_unix_session(5)NOTES
The pam_unix(5) module is no longer supported. Similar functionality is
provided by pam_authtok_check(5), pam_authtok_get(5), pam_auth‐
tok_store(5), pam_dhkeys(5), pam_passwd_auth(5), pam_unix_account(5),
pam_unix_auth(5), and pam_unix_session(5).
The service access controller service is managed by the service manage‐
ment facility, smf(5), under the service identifier:
svc:/system/sac:default
Administrative actions on this service, such as enabling, disabling, or
requesting restart, can be performed using svcadm(1M). The service's
status can be queried using the svcs(1) command.
SunOS 5.11 21 Apr 2009 sac(1M)