OPCONTROL(1)OPCONTROL(1)NAMEopcontrol - control OProfile profiling
SYNOPSISopcontrol [ options ]
DESCRIPTIONopcontrol can be used to start profiling, end a profiling session, dump
profile data, and set up the profiling parameters.
OPTIONS--help Show help message.
--version
Show version.
--list-events
Shows the monitorable events.
--init Load the OProfile module if required and make the OProfile
driver interface available.
--setup
Followed by list options for profiling setup. Store setup in
~root/.oprofile/daemonrc. Optional.
--status
Show configuration information.
--start-daemon
Start the oprofile daemon without starting profiling. Not avail‐
able in 2.2/2.4 kernels.
--start
Start data collection with either arguments provided by --setup
or with information saved in ~root/.oprofile/daemonrc.
--dump Force a flush of the collected profiling data to the daemon.
--stop Stop data collection. Not available in 2.2/2.4 kernels.
--shutdown
Stop data collection and kill the daemon.
--reset
Clear out data from current session, but leaves saved sessions.
--save=sessionname
Save data from current session to sessionname.
--deinit
Shut down daemon. Unload the oprofile module and oprofilefs.
--session-dir=dir_path
Use sample database out of directory dir_path instead of the
default location (/var/lib/oprofile).
--buffer-size=num
Set kernel buffer to num samples. When using a 2.6 kernel buffer
watershed need to be tweaked when changing this value.
--buffer-watershed=num
Set kernel buffer watershed to num samples (2.6 only). When
it'll remain only buffer-size - buffer-watershed free entry in
the kernel buffer data will be flushed to daemon, most usefull
value are in the range [0.25 - 0.5] * buffer-size.
--cpu-buffer-size=num
Set kernel per cpu buffer to num samples (2.6 only). If you pro‐
file at high rate it can help to increase this if the log file
show excessive count of sample lost cpu buffer overflow.
--event=[event|"default"]
Specify an event to measure for the hardware performance coun‐
ters, or "default" for the default event. The event is of the
form "CPU_CLK_UNHALTED:30000:0:1:1" where the numeric values are
count, unit mask, kernel-space counting, user-space counting,
respectively. Note that this over-rides all previous events
selected; if you want two or more counters used simultaneously,
you must specify them on the same opcontrol invocation.
--separate=[none,lib,kernel,thread,cpu,all]
Separate samples based on the given separator. 'lib' separates
dynamically linked library samples per application. 'kernel'
separates kernel and kernel module samples per application;
'kernel' implies 'library'. 'thread' gives separation for each
thread and task. 'cpu' separates for each CPU. 'all' implies
all of the above options and 'none' turns off separation.
--callgraph=#depth
Enable callgraph sample collection with a maximum depth. Use 0
to disable callgraph profiling. This option is available on x86
using a 2.6+ kernel with callgraph support enabled. It is also
available on PowerPC using a 2.6.17+ kernel.
--image=[name,name...|"all"]
Only profile the given absolute paths to binaries, or "all" to
profile everything (the default).
--vmlinux=file
vmlinux kernel image.
--no-vmlinux
Use this when you don't have a kernel vmlinux file, and you
don't want to profile the kernel.
--verbose
Be verbose in the daemon log. This has a high overhead.
--kernel-range=start,end
Set kernel range vma address in hexadecimal.
OPTIONS (specific to Xen)
--xen=file
Xen image
--active-domains=<list>
List of domain ids participating in a multi-domain profiling
session. If more than one domain is specified in <list> they
should be separated using commas. This option can only be used
in domain 0 which is the only domain that can coordinate a
multi-domain profiling session. Including domain 0 in the list
of active domains is optional. (e.g. --active-domains=2,5,6 and
--active-domains=0,2,5,6 are equivalent)
ENVIRONMENT
No special environment variables are recognised by opcontrol.
FILES
/root/.oprofile/daemonrc
Configuration file for opcontrol
/var/lib/oprofile/samples/
The location of the generated sample files.
VERSION
This man page is current for oprofile-0.9.4.
SEE ALSO
/usr/share/doc/oprofile/, oprofile(1)4th Berkeley Distribution Tue 20 January 2009OPCONTROL(1)
