MUNIN-NODE-CONFIGURE(1User Contributed Perl DocumentatiMUNIN-NODE-CONFIGURE(1)NAMEmunin-node-configure - View and modify which plugins are enabled.
SYNOPSISmunin-node-configure [options]
DESCRIPTIONmunin-node-configure reports which plugins are enabled on the current
node, and suggest changes to this list.
By default this program shows which plugins are activated on the
system.
If you specify "--suggest", it will present a table of plugins that
will probably work (according to the plugins' autoconf command).
If you specify "--snmp", followed by a list of hosts, it will present a
table of SNMP plugins that they support.
If you additionally specify "--shell", shell commands to install those
same plugins will be printed. These can be reviewed or piped directly
into a shell to install the plugins.
GENERAL OPTIONS--help
Show this help page.
--version
Show version information.
--debug
Print debug information on the operations of
"munin-node-configure". This can be very verbose.
All debugging output is printed to STDOUT, and each line is
prefixed with '#'. Only errors are printed to STDERR.
--pidebug
Plugin debug. Sets the environment variable MUNIN_DEBUG to 1 so
that plugins may enable debugging.
--config <file>
Override configuration file [/usr/local/etc/munin/munin-node.conf]
--servicedir <dir>
Override plugin directory [/usr/local/etc/munin/plugins/]
--sconfdir <dir>
Override plugin configuration directory
[/usr/local/etc/munin/plugin-conf.d/]
--libdir <dir>
Override plugin library [/usr/local/share/munin/plugins/]
--exitnoterror
Do not consider plugins that exit non-zero exit-value as error.
--suggest
Suggest plugins that might be added or removed, instead of those
that are currently enabled.
OUTPUT OPTIONS
By default, "munin-node-configure" will print out a table summarising
the results.
--shell
Instead of a table, print shell commands to install the new plugin
suggestions.
This implies "--suggest", unless "--snmp" was also enabled. By
default, it will not attempt to remove any plugins.
--remove-also
When "--shell" is enabled, also provide commands to remove plugins
that are no longer applicable from the service directory.
PLUGIN SELECTION OPTIONS
--families <family,...>
Override the list of families that will be used (auto, manual,
contrib, snmpauto). Multiple families can be specified as a comma-
separated list, by repeating the "--families" option, or as a
combination of the two.
When listing installed plugins, the default families are 'auto',
'manual' and 'contrib'. Only 'auto' plugins are checked for
suggestions. SNMP probing is only performed on 'snmpauto' plugins.
--newer <version>
Only consider plugins added to the Munin core since <version>.
This option is useful when upgrading, since it can prevent plugins
that have been manually removed from being reinstalled. This only
applies to plugins in the 'auto' family.
SNMP Options
--snmp <host|cidr,...>
Probe the SNMP agents on the host or CIDR network (e.g.
"192.168.1.0/24"), to see what plugins they support. This may take
some time, especially if the many hosts are specified.
This option can be specified multiple times, or as a comma-
separated list, to include more than one host/CIDR.
--snmpversion <ver>
The SNMP version (1, 2c or 3) to use. ['2c']
--snmpport <port>
The SNMP port to use [161]
SNMP 1/2c authentication
SNMP versions 1 and 2c use a "community string" for authentication.
This is a shared password, sent in plaintext over the network.
--snmpcommunity <string>
The community string for version 1 and 2c agents. ['public'] (If
this works your device is probably very insecure and needs a
security checkup).
SNMP 3 authentication
SNMP v3 has three security levels. Lowest is "noAuthNoPriv", which
provides neither authentication nor encryption. If a username and
"authpassword" are given it goes up to "authNoPriv", and the
connection is authenticated. If "privpassword" is also given the
security level becomes "authPriv", and the connection is
authenticated and encrypted.
Note: Encryption can slow down slow or heavily loaded network
devices. For most uses "authNoPriv" will be secure enough -- the
password is sent over the network encrypted in any case.
ContextEngineIDs are not (yet) supported.
For further reading on SNMP v3 security models please consult
RFC3414 and the documentation for Net::SNMP.
--snmpusername <name>
Username. There is no default.
--snmpauthpassword <password>
Authentication password. Optional when encryption is also enabled,
in which case defaults to the privacy password
("--snmpprivpassword").
--snmpauthprotocol <protocol>
Authentication protocol. One of 'md5' or 'sha' (HMAC-MD5-96,
RFC1321 and SHA-1/HMAC-SHA-96, NIST FIPS PIB 180, RFC2264).
['md5']
--snmpprivpassword <password>
Privacy password to enable encryption. There is no default. An
empty ('') password is considered as no password and will not
enable encryption.
Privacy requires a privprotocol as well as an authprotocol and a
authpassword, but all of these are defaulted (to 'des', 'md5', and
the privpassword value, respectively) and may therefore be left
unspecified.
--snmpprivprotocol <protocol>
If the privpassword is set this setting controls what kind of
encryption is used to achieve privacy in the session. Only the
very weak 'des' encryption method is supported officially. ['des']
munin-node-configure also supports '3des' (CBC-3DES-EDE, aka
Triple-DES, NIST FIPS 46-3) as specified in IETF
draft-reeder-snmpv3-usm-3desede. Whether or not this works with
any particular device, we do not know.
FILES
/usr/local/etc/munin/munin-node.conf
/usr/local/etc/munin/plugin-conf.d/*
/usr/local/etc/munin/plugins/*
/usr/local/share/munin/plugins/plugins.history
/usr/local/share/munin/plugins/*
VERSION
This is munin-node-configure (munin-node) v2.0.25.
$Id$
AUTHORS
Jimmy Olsen, Nicolai Langfeldt, Matthew Boyle
BUGS
Please see <http://munin-monitoring.org/report/1>.
COPYRIGHT
Copyright (C) 2003-2006 Jimmy Olsen, Nicolai Langfeldt.
Copyright (C) 2009-2010 Matthew Boyle
This is free software; see the source for copying conditions. There is
NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE.
This program is released under the GNU General Public License
perl v5.20.3 2016-02-19 MUNIN-NODE-CONFIGURE(1)
