GET-OUI(1)GET-OUI(1)NAMEget-oui - Fetch the arp-scan OUI file from the IEEE website
SYNOPSISget-oui [options]
DESCRIPTIONget-oui fetches the Ethernet OUI file from the IEEE website, and saves
it in the format used by arp-scan.
The OUI file contains all of the OUIs (Organizationally Unique Identi‐
fiers) that have been registered with IEEE. Each OUI entry in the file
specifies the first 24-bits of the 48-bit Ethernet hardware address,
leaving the remaining 24-bits for use by the registering organisation.
For example the OUI entry "080020", registered to Sun Microsystems,
applies to any Ethernet hardware address from 08:00:20:00:00:00 to
08:00:20:ff:ff:ff inclusive. Each OUI assignment represents a total of
2^24 (16,777,216) Ethernet addresses.
Every major Ethernet hardware vendor registers an OUI for their equip‐
ment, and larger vendors will need to register more than one. For
example, 3Com have a total of 37 OUI entries. Organisations that only
produce a small number of Ethernet devices will often obtain an IAB
registration instead. See get-iab(1) for details.
This script can be used to update the arp-scan OUI file from the latest
data on the IEEE website. Most of the Ethernet addresses in use belong
to an OUI registration, so this is the most important of the files that
arp-scan uses to decode Ethernet hardware addresses. You should there‐
fore run get-oui occasionally to keep the arp-scan OUI file up to date.
The OUI data is fetched from the URL http://stan‐
dards.ieee.org/regauth/oui/oui.txt and the output file is saved to the
file ieee-oui.txt in the current directory. The URL to fetch the data
from can be changed with the -u option, and the output file name can be
changed with the -f option.
The ieee-oui.txt file that is produced by this script is used by arp-
scan to determine the Ethernet card vendor from its hardware address.
The directory that arp-scan will look for the ieee-oui.txt file depends
on the options used when it was built. If it was built using the
default options, then it will look in /usr/local/share/arp-scan.
OPTIONS-h Display a brief usage message and exit.
-f <fn>
Write the output to the specified file instead of the default
ieee-oui.txt.
-u <URL>
Use the specified URL to fetch the raw OUI data from instead of
the default http://standards.ieee.org/regauth/oui/oui.txt.
-v Display verbose progress messages.
FILES
ieee-oui.txt
The default output file.
EXAMPLES
$ get-oui-v
Renaming ieee-oui.txt to ieee-oui.txt.bak
Fetching OUI data from http://standards.ieee.org/regauth/oui/oui.txt
Fetched 1467278 bytes
Opening output file ieee-oui.txt
9274 OUI entries written to file ieee-oui.txt
NOTESget-oui is implemented in Perl, so you need to have the Perl inter‐
preter installed on your system to use it.
get-oui uses the LWP::Simple Perl module to fetch the data from the
IEEE website. You must have this module installed on your system for it
to work. This module is available on most distributions, often called
libwww-perl. It is also available in source form from CPAN.
You can use a proxy server by defining the http_proxy environment vari‐
able.
AUTHOR
Roy Hills <Roy.Hills@nta-monitor.com>
SEE ALSOarp-scan(1)get-iab(1)arp-fingerprint(1)
http://www.nta-monitor.com/wiki/ The arp-scan wiki page.
March 30, 2007 GET-OUI(1)
