lsscsi man page on Scientific
Printed from http://www.polarhome.com/service/man/?qf=lsscsi&af=0&tf=2&of=Scientific
lsscsi(8) LSSCSI lsscsi(8)
NAME
lsscsi - list SCSI devices (or hosts) and their attributes
SYNOPSIS
lsscsi [--classic] [--device] [--generic] [--help] [--hosts] [--kname]
[--list] [--long] [--protection] [--sysfsroot=PATH] [--transport]
[--verbose] [--version] [H:C:T:L]
DESCRIPTION
Uses information in sysfs (linux kernel series 2.6 and later) to list
scsi devices (or hosts) currently attached to the system. Options can
be used to control the amount and form of information provided for each
device.
If a H:C:T:L argument is given then it acts as a filter and only
devices that match it are listed. The colons don't have to be present,
and '-', '*', '?' or missing arguments at the end are interpreted as
wildcards. '-' needs to stand alone or else it is taken as the begin‐
ning of an option (e.g. '-:-:-:-' is illegal). '*' needs to be escaped
from the shell. A leading '[' and trailing ']' are permitted (e.g.
'[1:0:0]' matches all luns on 1:0:0). May also be used to filter
--hosts in which case only the H is active and may be either a number
or in the form "host<n>" where <n> is a host number.
By default in this utility device node names (e.g. "/dev/sda" or
"/dev/root_disk") are obtained by noting the major and minor numbers
for the listed device obtained from sysfs (e.g. the contents of
"/sys/block/sda/dev") and then looking for a match in the "/dev" direc‐
tory. This "match by major and minor" will allow devices that have been
given a different name by udev (for example) to be correctly reported
by this utility.
In some situations it may be useful to see the device node name that
linux would produce by default, so the --kname option is provided. An
example of where this may be useful is kernel error logs which tend to
report disk error messages using the disk's default kernel name.
Information about this utility including examples can also be found at:
http://sg.danny.cz/scsi/lsscsi.html .
OPTIONS
-c, --classic
The output is similar to that obtained from 'cat
/proc/scsi/scsi'
-d, --device
After outputting the (probable) scsi device name the device node
major and minor numbers are shown in brackets (e.g.
"/dev/sda[8:0]").
-g, --generic
Output the scsi generic device file name. Note that if the sg
driver is a module it may need to be loaded otherwise '-' may
appear.
-h, --help
Output the usage message and exit.
-H, --hosts
List the SCSI hosts currently attached to the system. If this
option is not given then SCSI devices are listed.
-k, --kname
Use linux default algorithm for naming devices (e.g. block major
8, minor 0 is "/dev/sda") rather than the "match by major and
minor" in the "/dev" directory as discussed above.
-L, --list
Output additional information in <attribute_name>=<value> pairs,
one pair per line preceded by two spaces. This option has the
same effect as '-lll'
-l, --long
Output additional information for each SCSI device (host). Can
be used multiple times for more output in which case the shorter
option form is more convenient (e.g. '-lll'). When used three
times (i.e. '-lll') outputs SCSI device (host) attributes one
per line; preceded by two spaces; in the form
"<attribute_name>=<value>".
-p, --protection
Output additional data integrity (protection) information.
-t, --transport
Output transport information. This will be a target related
information or, if --hosts is given, initiator related informa‐
tion. When used without --list, a name or identifier (or both)
are output on a single line, usually prefixed by the type of
transport. For devices this information replaces the normal ven‐
dor, product and revision strings. When the --list option is
also given then additionally multiple lines of
attribute_name=value pairs are ouput, each indented by two spa‐
ces. See the section on transports below.
-v, --verbose
outputs directory names where information is found. Use multiple
times for more output.
-V, --version
outputs version information then exits.
-y, --sysfsroot=PATH
assumes sysfs is mounted at PATH instead of the default '/sys' .
If this option is given PATH should be an absolute path (i.e.
start with '/').
NOTES
Information for this command is derived from the sysfs file system,
which is assumed to be mounted at /sys unless specified otherwise by
the user. SCSI (pseudo) devices that have been detected by the SCSI
mid level will be listed even if the required upper level drivers (i.e.
sd, sr, st, osst or ch) have not been loaded. If the appropriate upper
level driver has not been loaded then the device file name will appear
as '-' rather than something like '/dev/st0'. Note that some devices
(e.g. scanners and medium changers) do not have a primary upper level
driver and can only be accessed via a scsi generic (sg) device name.
lsscsi version 0.21 or later is required to correctly display SCSI
devices in linux kernel 2.6.26 (and possibly later) when the CON‐
FIG_SYSFS_DEPRECATED_V2 kernel option is not defined.
TRANSPORTS
This utility lists SCSI devices which are known as logical units (lu)
in the SCSI Architecture Model (ref: SAM-4 at http://www.t10.org) or
hosts when the --hosts option is given. A host is called an initiator
in SAM-4. A SCSI command travels out via an initiator, across some
transport to a target and then onwards to a logical unit. A target
device may contain several logical units. A target device has one or
more ports that can be viewed as transport end points. Each FC and SAS
disk is a single target that has two ports and contains one logical
unit. If both target ports on a FC or SAS disk are connected and visi‐
ble to a machine, then lsscsi will show two entries. Initiators (i.e.
hosts) also have one or more ports and some HBAs in Linux have a host
entry per initiator port while others have a host entry per initiator
device.
When the --transport option is given for devices (i.e. --hosts not
given) then most of the information produced by lsscsi is associated
with the target, or more precisely: the target port, through which SCSI
commands pass that access a logical unit.
Typically this utility provides one line of output per "device" or
host. Significantly more information can be obtained by adding the
--list option. When used together with the --transport option, after
the summary line, multiple lines of transport specific information in
the form "<attribute_name>=<value>" are output, each indented by two
spaces. Using a filter argument will reduce the volume of output if a
lot of devices or hosts are present.
The transports that are currently recognized are: IEEE 1394, ATA, FC,
iSCSI, SAS, SATA, SPI and USB.
For IEEE 1394 (a.k.a. Firewire and "SBP" when storage is involved), the
EUI-64 based target port name is output when --transport is given, in
the absence of the --hosts option. When the --hosts option is given
then the EUI-64 initiator port name is output. Output on the summary
line specific to the IEEE 1394 transport is prefixed by "sbp:".
to detect ATA and SATA a crude check is performed on the driver name
(after the checks for other transports are exhausted). Based on the
driver name either ATA or SATA transport type is chosen. Output on the
summary line is either "ata:" or "sata:". No other attributes are
given. Most device and hosts flagged as "ata:" will use the parallel
ATA transport (PATA).
For Fibre Channel (FC) the port name and port identifier are output
when --transport is given. In the absence of the --hosts option these
ids will be for the target port associated with the device (logical
unit) being listed. When the --hosts option is given then the ids are
for the initiator port used by the host. Output on the summary line
specific to the FC transport is prefixed by "fc:".
For iSCSI the target port name is output when --transport is given, in
the absence of the --hosts option. This is made up of the iSCSI name
and the target portal group tag. Since the iSCSI name starts with "iqn"
no further prefix is used. When the --hosts option is given then only
"iscsi:" is output on the summary line.
For Serial Attached SCSI the SAS address of the target port (or initia‐
tor port if --hosts option is also given) is output. This will be a
naa-5 address. For SAS HBAs and SAS targets (such as SAS disks and tape
drives) the SAS address will be world wide unique. For SATA disks
attached to a SAS expander, the expander provides the SAS address by
adding a non zero value to its (i.e. the expander's) SAS address (e.g.
expander_sas_address + phy_id + 1). SATA disks directly attached to SAS
HBAs seem to have an indeterminate SAS address. Output on the summary
line specific to the SAS transport is prefixed by "sas:".
For the SCSI Parallel Interface (SPI) the target port identifier (usu‐
ally a number between 0 and 15 inclusive) is output when --transport is
given, in the absence of the --hosts option. When the --hosts option is
given then only "spi:" is output on the summary line.
When a USB transport is detected, the summary line will contain "usb:"
followed by a USB device name. The USB device name has the form
"<b>-<p1>[.<p2>[.<p3>]]:<c>.<i>" where <b> is the USB bus number, <p1>
is the port on the host. <p2> is a port on a host connected hub, if
present. If needed <p3> is a USB hub port closer to the USB storage
device. <c> refers to the configuration number while <i> is the inter‐
face number. There is a separate SCSI host for each USB (SCSI) target.
A USB SCSI target may contain multiple logical units. Thus the same
"usb: <device_name>" string appears for a USB SCSI host and all logical
units that belong to the USB SCSI target associated with that USB SCSI
host.
AUTHOR
Written by Doug Gilbert
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2003-2009 Douglas Gilbert
This software is distributed under the GPL version 2. There is NO war‐
ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR‐
POSE.
SEE ALSO
lspci lsusb
lsscsi-0.23 November 2009 lsscsi(8)
[top]
List of man pages available for Scientific
Copyright (c) for man pages and the logo by the respective OS vendor.
For those who want to learn more, the polarhome community provides shell access and support.
[legal]
[privacy]
[GNU]
[policy]
[cookies]
[netiquette]
[sponsors]
[FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
|
Vote for polarhome
|